How Much Is a 100 Foot Concrete Driveway in 2026?

How Much Is a 100 Foot Concrete Driveway in 2026?

How much is a 100 foot concrete driveway in 2026? It depends on the width, because contractors price by the square foot: a 100-foot driveway that is 12 feet wide (1,200 square feet) typically costs $7,200–$14,400 for a plain broom finish installed, and a 100-foot driveway that is 20 feet wide (2,000 square feet) typically costs $12,000–$24,000 plain. With old driveway removal added, the 12-foot-wide version runs $9,600–$19,200 all-in, and stamped or decorative concrete roughly doubles the plain price at any width. The per-square-foot rate behind those totals is $6–$12 for plain concrete and $12–$20 for stamped concrete. This guide breaks down the 100-foot driveway cost by width, finish, and site condition, so you can price your exact driveway instead of guessing from a length alone.

A 100-foot driveway is a long driveway — common on rural lots, flag lots, and properties set far back from the street. Its length is also why the width matters so much: every extra foot of width adds 100 square feet, which at $6–$12 per square foot is $600–$1,200 per foot of width. A 10-foot-wide single-lane drive and a 20-foot-wide double drive are both “100 foot driveways” but differ by $6,000 or more.

For background on concrete itself, the Portland Cement Association publishes concrete basics and technical guidance at cement.org, and the National Ready Mixed Concrete Association covers ready-mix concrete production and standards at nrmca.org.

Quick-answer table (typical 2026 cost of a 100 foot concrete driveway, plain broom finish):

How Much Is a 100 Foot Concrete Driveway by Width

Width is the multiplier on a long driveway, so measure yours before you compare quotes. A 100-foot driveway is usually built in one of these widths:

Single-lane drives (10–12 feet wide) are the most common 100-foot driveways. A 12-foot width gives comfortable room for one car with space to open doors, and at 1,200 square feet it is the sweet spot for pricing: large enough that crews offer a better per-square-foot rate than a small pad, small enough that the total stays manageable. If your driveway is a single lane, $7,200–$14,400 plain is the number to compare quotes against.

Two-car-width drives (20 feet wide) double the area and roughly double the price. They are worth it only if two cars genuinely need to pass or park side by side along the full length; a cheaper alternative is a 12-foot drive with a widened parking pad near the house, which gives you two-car parking where it matters without paying for 2,000 square feet of concrete. For a standard two-car example, see our guide to how much a 20×20 concrete driveway costs.

Long driveways often get a better per-square-foot rate. Setup, forming, and crew mobilization are spread over more square feet, so contractors frequently price a 1,200-square-foot drive at the lower end of the $6–$12 range, while a 400-square-foot pad lands in the middle. If your quotes cluster near $6–$8 per square foot for plain concrete, that is the long-driveway discount working in your favor — not a sign of a corner being cut, as long as thickness and base depth are confirmed in writing.

What the 100 Foot Price Includes — and What It Does Not

A typical installed quote includes excavation to depth, a compacted gravel base (usually 4 inches), forming, concrete, pouring, finishing, and control joints. These items are often priced separately on a long driveway:

The all-in math for the typical 12-foot-wide job. Plain broom finish ($7,200–$14,400) + old driveway removal ($1,200–$4,800) = $8,400–$19,200, and adding basic grading or a first sealing application brings most real projects to the $9,600–$19,200 all-in range in the quick-answer table. If your project is new construction on bare ground with no removal, the plain total of $7,200–$14,400 is the number to compare against.

Length creates its own cost drivers. A 100-foot pour may be done in sections over 2–3 days rather than a single day, which adds crew days. Access matters more: if concrete trucks cannot reach the far end, the crew pumps concrete or wheelbarrows it, and pumping adds $500–$1,500. Drainage matters more too — a 100-foot slab needs a consistent slope away from the house and often a crown or channel drain so water does not pool mid-drive. Ask every bidder how they handle slope, joints, and truck access along the full length, not just near the street.

For the full tear-out pricing, see the cost to remove and replace a concrete driveway.

100 Foot Driveway Cost by Region

Concrete material costs are fairly uniform nationally, so regional differences are almost entirely labor and delivery distance. On a long rural driveway, delivery distance is a real factor: if the batch plant is far away, expect a delivery surcharge or a minimum-load fee, and ask whether the quote includes it.

Concrete vs Asphalt for a 100 Foot Driveway

Asphalt is cheaper upfront on a long driveway too — roughly $1,200–$2,400 less on a 12×100 drive — but the 30-year gap is even wider than on a short driveway because the replacement bill scales with area: replacing 1,200 square feet of asphalt costs $6,000–$12,000 all over again. If you plan to stay, concrete’s lifetime advantage grows with every foot of length.

DIY vs. Hiring a Pro

A 100-foot driveway is a poor DIY candidate even by concrete standards: the pour must be sectioned correctly, the slope must stay consistent for 100 feet, and concrete sets in hours, so a slow crew ends up with visible cold joints between sections. Most homeowners are better off hiring a pro for the full pour and reserving DIY for sealing and small repairs. Whatever you choose, do not drive on a new driveway for at least 7 days, and wait the full 28 days before parking heavy vehicles on it.

Money-Saving Tips

1. Measure width before you price. A 12-foot drive costs roughly 40% less than a 20-foot drive of the same length — do not pay for width you do not need. 2. Use a parking pad instead of full width. A 12-foot drive plus a pad near the house gives two-car parking for far less than a 20-foot-wide drive. 3. Get three quotes on the same basis: same width, finish, thickness, base depth, and removal scope. 4. Confirm thickness and reinforcement in writing. A 4-inch slab with mesh or rebar is the minimum for a driveway that lasts. 5. Choose plain broom finish unless a decorative look is worth roughly double the price to you. 6. Ask about pumping and delivery fees upfront. On a long driveway, access surcharges are the most common surprise line item. 7. Seal on schedule. A $600–$1,500 sealing every 3–5 years prevents stains and freeze-thaw damage that cost thousands to repair.

Frequently Asked Questions

How much is a 100 foot concrete driveway?

Typically $7,200–$14,400 for a 12-foot-wide plain driveway (1,200 square feet), $12,000–$24,000 at 20 feet wide (2,000 square feet), and $9,600–$19,200 all-in with old driveway removal for the 12-foot width.

How many square feet is a 100 foot driveway?

It depends on width: 100 feet long by 12 feet wide is 1,200 square feet; by 20 feet wide it is 2,000 square feet. Multiply length by width to get your exact area.

How thick should a 100 foot concrete driveway be?

4 inches for passenger cars, 5 inches if pickup trucks or SUVs use it regularly, and 6 inches for RVs or heavy vehicles. Control joints every 10–12 feet help manage cracking over a long run.

How long does a 100 foot concrete driveway take to install?

The pour itself takes 2–3 days in sections, but the full timeline is 10–14 days: 2–3 days for excavation and base preparation, 2–3 days for forming and pouring, and 5–7 days of curing before light vehicle use. Full concrete strength is reached at 28 days.

Is a 100 foot concrete driveway cheaper than asphalt?

No — concrete costs about 20% more upfront for the same dimensions ($7,200–$14,400 plain versus $6,000–$12,000 for asphalt on a 12×100 drive). But concrete lasts 25–50 years versus 15–20 for asphalt, so it is usually cheaper over its full life.

Do I need a permit for a 100 foot concrete driveway?

It varies by city: permits typically cost $50–$300 where required, and some areas require none for a like-for-like replacement. Long driveways that cross a ditch or connect to a public road may also need an apron or culvert approval — check with your local building department before pouring.

The Bottom Line

For a 100 foot concrete driveway in 2026, budget $7,200–$14,400 for a 12-foot-wide plain driveway, $12,000–$24,000 at 20 feet wide, and $9,600–$19,200 all-in with removal for the 12-foot width — then add stamped or decorative finishes only if the look is worth roughly double the plain price. Measure your width, get three quotes on the same finish, thickness, and base depth, confirm pumping and access fees upfront, and remember that the per-square-foot rate is your best check: if the math does not work at $6–$12 per square foot for plain concrete, the quote does not work either.

Prices are typical 2026 US ranges for planning purposes and vary by region, material grade, and site condition; get itemized local quotes for an exact project price.